Kitchen Plumbing Solutions in Palos Heights, IL
Kitchen plumbing can be straightforward or more involved depending on your plans. Whether you’re replacing a faucet and hooking up a garbage disposal in a few hours or planning a full remodel involving sink relocation, a new gas line for the stove, or adding a pot filler, we’ve got you covered. Every project varies in cost and schedule, and sometimes permits are necessary. No matter the job, our team handles it professionally.
If you’re remodeling, my recommendation is to get your plumber involved early — before cabinets go in. Moving sinks means reworking drains while subfloors are exposed, and running gas lines to an island or new spot must be done prior to cabinetry. Pot fillers require opening the wall behind the range, which is much easier before backsplash tile is installed. Contact us at 708-726-8793 to plan ahead and avoid delays.
We also handle one-off kitchen plumbing tasks like faucet swaps, disposal repairs or installs, dishwasher hookups, and refrigerator water line connections for homes that aren’t being remodeled. Kitchen remodels are a great time to check your water heater capacity and clear any slow drains before reinstalling cabinetry. Give us a call at 708-726-8793 for these services and more.
Our Kitchen Plumbing Services
Sink & Faucet Setup
We work with all sink styles — undermounts that need precise countertop cuts, drop-ins, farmhouse/apron front sinks, single or double bowls, and prep sinks. Installation includes fitting the drain assembly, strainer, P-trap, and connecting water supplies with durable braided stainless steel lines (none of that brittle plastic). We also install garbage disposals during the same visit if needed.
For faucets, we manage every type and configuration — one-hole, three-hole, deck-mounted — and rigorously test for leaks before finishing. Relocating a sink is a bigger task involving rerouting drains, adjusting vents, and extending water lines. We handle the necessary permits and inspections to get it done right.
Appliance Water & Drain Connections
Dishwasher connections include hooking up hot water supply, installing the drain line with the proper high loop or air gap to prevent contamination, and double-checking the electrical setup (we work alongside your electrician). For refrigerators with ice makers or water dispensers, we run a dedicated cold water line, usually copper or braided stainless, mounted with a shutoff valve easy to reach behind the fridge.
We also install instant hot water taps, under-sink filtration systems, and reverse osmosis units. Installing an RO includes drilling the faucet hole, connecting supply and drain lines, and advising on filter maintenance. Call us at 708-726-8793 for any of these appliance hookups.
Gas Line Installation for Kitchen Appliances
Whether upgrading from electric to gas or adding a gas cooktop to an island, we run new gas lines sized correctly for your appliance’s BTU rating. We bring the line from your gas meter or main supply, install a shutoff valve, fit a code-approved flexible connector, pressure-test the system, and take care of permits and inspections. For full details, check out our gas line service page.
Important: gas rough-in should occur before cabinets are installed since retrofitting gas lines afterward is messy and difficult. Coordinate this with your general contractor and us early so everything fits your timeline.
Pot Filler Faucet Installation
A pot filler faucet mounts on the wall above your stove, letting you fill pots without lugging them from the sink. It needs a cold water supply line run inside the wall roughly 56 to 60 inches above the floor and offset about 4 inches from the stove’s centerline. It’s easiest to install during a remodel when the wall is open, but we can add these in finished kitchens with careful wall patching and finishing. Reach out at 708-726-8793 to discuss your project.
Island Sink Plumbing & Drain Venting
Installing a sink on an island requires special venting since you can’t tie drains into wall vents like usual. Your local code will call for either an island loop vent or an air admittance valve (AAV) to keep things flowing properly. Water supply lines run easily from the nearest source, but routing drains and vents beneath the floor to the island cabinet takes precision. We’re experienced with island sink setups — call us early to plan your layout right.
Essential Kitchen Plumbing Checklist
- Removing and installing sinks of all types (undermount, farmhouse, drop-in)
- Installing faucets in all configurations
- Garbage disposal installation or replacement
- Connecting dishwashers to water supply and drain
- Running water lines for refrigerator ice makers
- Gas line installation for ranges, cooktops, and ovens
- Rough-in and installation of pot filler faucets
- Under-sink water filtration and reverse osmosis systems
- Drain and vent routing for island sinks
- Upgrading shutoff valves throughout the kitchen
- Installing prep or bar sinks in pantries or islands
Kitchen Plumbing Scheduling Tips
- Confirm sink placement before demolition: Moving your sink adds cost and complexity, so lock down the spot before ordering cabinets.
- Complete gas line rough-in before cabinetry: Running gas lines is easier before cabinets are installed.
- Install pot fillers early: It’s simpler to open walls before backsplash tile goes up.
- Upgrade shutoff valves while accessible: Replace old gate valves with ball valves when plumbing is exposed to avoid future leaks.
- Run refrigerator water lines before countertops: Easier to install before countertops are set.
Frequently Asked Kitchen Plumbing Questions
Yes, but it’s one of the more complicated changes because island sinks need special venting like an island loop vent or an air admittance valve (AAV) since there’s no wall vent nearby. Water supply is straightforward, but the drain and vent lines must be carefully planned and installed under the floor. We handle these installations regularly — give us a call at 708-726-8793 before finalizing your island design.
If you’re just swapping out fixtures in the same spot (like faucets or disposals), usually no permit is needed. But if you’re rerouting any drains, running new supply lines, installing gas lines, or changing the plumbing layout, then permits are required. We handle all permit applications and inspection scheduling as part of our service.
Definitely. Installing gas lines is best done when walls and floors are open, like during a remodel. We size the line properly, install shutoff valves, pressure test everything, and secure all permits. Plan to have your gas rough-in completed before cabinets go in. Check our gas line services page for details.
Yes, we work closely with general contractors, kitchen designers, and remodelers. We fit our plumbing schedules around your project timeline and manage permits so everything flows smoothly. Call 708-726-8793 early to get us on your team.